GB/T 2664-2009 男西服、大衣

作者:标准资料网 时间:2024-05-02 14:46:26   浏览:8434   来源:标准资料网
下载地址: 点击此处下载
基本信息
标准名称:男西服、大衣
英文名称:Mens suits and coats
中标分类: 轻工、文化与生活用品 >> 服装、鞋、帽与其他缝制品 >> 服装、服饰品
ICS分类: 服装工业 >> 服装
替代情况:替代GB/T 2664-2001
发布部门:中华人民共和国国家质量监督检验检疫总局 中国国家标准化管理委员会
发布日期:2009-03-19
实施日期:2010-01-01
首发日期:1981-05-29
作废日期:
主管部门: 中国纺织工业协会
提出单位:中国纺织工业协会
归口单位:全国服装标准化技术委员会(SAC/TC 219)
起草单位:上海市服装研究所、杭州市质量技术监督检测院、温州市质量技术监督检测院等
起草人:许鉴、顾红烽、林欧文、林月梅、林德培、盛志飞、沈应琴等
出版社:中国标准出版社
出版日期:2010-01-01
页数:20页
计划单号:20072331-T-608
适用范围

本标准规定了男西服、大衣的要求、检测方法、检验分类规则,以及标志、包装、运输和贮存等。
本标准适用于以毛、毛混纺及交织品、仿毛等机织物为主要面料生产的男西服、大衣等毛呢类服装。

前言

没有内容

目录

没有内容

引用标准

下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件,其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准,然而,鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件,其最新版本适用于本标准。
GB/T250 纺织品 色牢度试验 评定变色用灰色样卡
GB/T1335.1 服装号型 男子
GB/T1335.3 服装号型 儿童
GB/T2910 纺织品 二组分纤维混纺产品定量化学分析方法
GB/T2911 纺织品 三组分纤维混纺产品定量化学分析方法
GB/T2912.1 纺织品 甲醛的测定 第1部分:游离和水解的甲醛(水萃取法)
GB/T3917.2 纺织品 织物撕破性能 第2 部分:裤形试样(单缝)撕破强力的测定
GB/T3920 纺织品 色牢度试验 耐摩擦色牢度
GB/T3921 纺织品 色牢度试验 耐皂洗色牢度
GB/T4802.1 纺织品 织物起毛起球性能的测定 第1部分:圆轨迹法
GB/T4841.3 染料染色标准深度色卡2/1、1/3、1/6、1/12、1/25
GB5296.4 消费品使用说明 纺织品和服装使用说明
GB/T5711 纺织品 色牢度试验 耐干洗色牢度
GB/T5713 纺织品 色牢度试验 耐水色牢度
GB/T7573 纺织品 水萃取液pH 值的测定
GB/T8170 数值修约规则及极限数值的表示和判定
GB/T8427-2008 纺织品 色牢度试验 耐人造光色牢度:氙弧
GB/T8630 纺织品洗涤和干燥后尺寸变化的测定
GB/T14304 毛呢套装规格
GB/T16988 特种动物纤维与绵羊毛混合物含量的测定
GB/T17592 纺织品 禁用偶氮染料的测定
GB18401 国家纺织产品基本安全技术规范
FZ/T01026 纺织品 四组分纤维混纺产品定量化学分析方法
FZ/T01048 蚕丝/羊绒混纺产品混纺比的测定
FZ/T01053 纺织品 纤维含量的标识
FZ/T01057(所有部分) 纺织纤维鉴别试验方法
FZ/T80002 服装标志、包装、运输和贮存
FZ/T80004 服装成品出厂检验规则
FZ/T80007.1 使用粘合衬服装剥离强度测试方法
FZ/T80007.3 使用粘合衬服装耐干洗测试方法

所属分类: 轻工 文化与生活用品 服装 鞋 帽与其他缝制品 服装 服饰品 服装工业 服装
下载地址: 点击此处下载
【英文标准名称】:StandardMethodsofFireTestsforEvaluatingContributionofWallandCeilingInteriorFinishtoRoomFireGrowth
【原文标准名称】:评估墙壁及天花板室内装饰至室内火灾增长的防火测试标准方法
【标准号】:ANSI/NFPA286-2011
【标准状态】:现行
【国别】:美国
【发布日期】:2011
【实施或试行日期】:
【发布单位】:美国国家标准学会(US-ANSI)
【起草单位】:ANSI
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:Firetechnology;Firetests;Flammability;Interiorfinishes;Surfacespreadofflame;Testing
【摘要】:1-1.1*Thisstandarddescribesamethodfordeterminingthecontributionofinteriorfinishmaterialstoroomfiregrowthduringspecifiedfireexposureconditions.Thismethodshallbeusedtoevaluatetheflammabilitycharacteristicsofwallandceilinginteriorfinish,otherthantextilewallcoverings,wheresuchmaterialsconstitutetheexposedinteriorsurfacesofbuildings.1-1.2Thisfiretestmethodshallnotbeintendedtoevaluatethefireenduranceofassemblies,norshallitbeabletoevaluatetheeffectoffiresthatoriginatewithinawallassembly.1-1.3Thisstandardspecifiesthreetypesofspecimenmounting,dependingontheapplicationoftheinteriorfinishmaterial,asfollows:(1)Threewalls(forinteriorfinishtobeusedonwallsonly)(2)Threewallsandtheceiling(forinteriorfinishtobeusedonwallsandceilings)(3)Theceilingalone(forinteriorfinishtobeusedonceilingsonly).
【中国标准分类号】:P16
【国际标准分类号】:13_220_40;13_220_50
【页数】:
【正文语种】:英语


Product Code:SAE J968/1
Title:Diesel Injection Pump Testing--Part 1: Calibrating Nozzle and holder assemblies
Issuing Committee:Diesel Fuel Injection Equipment Standards Committee
Scope:This part of SAE J968 specifies two types of calibrating nozzle and holder assemblies intended for the testing and setting of diesel injection pumps on test benches. It applies to: a. A calibrating nozzle and holder assembly with a single hole orifice plate; b. A calibrating nozzle and holder assembly with a delay pintle type nozzle.The approximate range of the calibrating nozzle and holder assembly is up to: a. 300 mm{sup}3/stroke with the single hole orifice plate; b. 150 mm{sup}3/stroke with the delay pintle type nozzle. Setting and maintenance requirements are specified in ISO 4008/3.